News-Jiangsu Degao Machinery Co., Ltd

1、Definition: Pig feed is usually composed of protein feed, energy feed, roughage silage feeding materials, minerals, green feed, feed and feed additives; By category: full price, concentrates and premix. 2、Type: Pig has a variety of commonly used feed, according to the nutrition into energy feed, protein feed, roughage, green feed, silage feeding materials, mineral eight kinds of feed and feed additives. 3、About hormone: now basically has added a variety of hormones and antibiotics in pig feed, in order to make the pig meat fast and long lean lean, take a lot of hormone and clenbuterol in feed, in order to pig skin brightness, to add urea and arsenic preparation, in order to pig don't get sick, to add antibiotics and so on. 4、Note: （1）Selection of raw material variety as much as possible raw material variety can have the complementary role of nutrients, but must pay attention to the pig. Nutrient use efficiency in the raw material. （2）The quality of feed ingredients to conform to the standard purchasing raw materials can be in accordance with the national standard, avoid by all means purchasing cheap and inferior raw material. （3）As far as possible the use of local cheap feed raw materials The local feed raw material resources is not the same, some cheap feed ingredients such as rice bran, tofu, can take advantage of, in order to reduce production cost. （4）Feed raw material supply is plentiful For some sometimes no raw material, it is best to avoid using, often because of change the raw material, can cause stress to the pigs. （5）Pay attention to the palatability of feed ingredients Although some raw materials are very cheap, but it isn't palatability, attention should be paid to limit the amount of such materials. On the contrary, for those who are very good palatability raw material, also want to consider to feed restriction, to prevent overeating and digestive problems. （6）Strictly according to the breed standard design recipes, conceptions of avoid by all means Feeding standard were made according to the results of feeding trials, more authoritative standards include the NRC standard, British standard of ARC and the national standard of our country. （7）Mixed evenly Some add less of the raw materials have to be premixed first, and then wait to be added to the aniseed mixed in

2016

Feed processing method of feed machinery and machine structure

Production TuSiLiao need those machines, according to the size of different yield of different is that some of the differences. But it is not a great difference. In general machine has used in the production TuSiLiao: crusher, feed pellet machine, feed mixer, this a few is imperative. There could be other equipment, screening equipment, cooling equipment, all kinds of auxiliary equipment, shaq dragon, blower, belt machine, packaging machine, boiler, etc. 1、Base: play the role of the connecting parts and bearing mill, make them form a whole. Shredded material is being exhausted from the base. 2、Rotor: the main shaft, hammer frame plate, pin shaft, bearings and other parts, hammer, is the main moving parts of crusher. Rotor speed is higher, assembled on without pin and hammer into the dynamic balance test. 3、Operate the door: replace the sieve plate or hammer to open door operation. Crusher work by locks lock door operation, ensure the operation of rotor rotating door can't open on its own. 4、On the chassis: upper feeding mouth, lower connection with base, sieve plate on both sides respectively equipped, and the rotor of the crushing chamber, the material in crushing chamber to smash. 5、Feeding guide mechanism: make the material from the left or right into the crushing chamber. Feeding guide plate of the reversing manual control to ensure the feed direction consistent with the rotor turning. 6、Fixed in powder pressure screen structure: the locking device connected, ensure that screen surface inside the mill. 7、Sieve sieve beam: sieve beam and pressure institutions together to screen piece fixed on the shredder. Production of feed mill adopts double rotor structure, greatly improve the working efficiency.

2016

Proper use of feed mill

Proper use of feed mill 1、Mill operation for a long time, should be fixed on the basis of cement. If change often work site, grinder with the motor installed on the made of Angle iron frame, if mill diesel power, should make the two power match, namely power slightly bigger than the mill power of diesel engine, and make the pulley groove of the two is consistent, pulley end on the same plane. 2、Mill after installation to check each fastener tighten situation, if there is loose should be tightened. 3、To check whether the belt elasticity is appropriate, whether the motor shaft and crusher shaft parallel. 4、Before starting the grinder, rotating the rotor by hand, and check the tooth claw hammer, and rotor operation is flexible and reliable, and there are no collisions in the shell, rotor rotate to whether in direction arrow on board, motor and shatter machine lubrication are in good condition. 5、Don't change the pulley, in case of high speed crushing chamber to produce explosion, or low speed impact work efficiency. 6、Crushing machine idle first 2 a 3 minutes after launch, no anomalies feeding again after work. 7、Work should pay attention to the workings of the crusher of at any time, feeding wants even, in case of blocking stuffy car, don't long time overload running. If find any vibration, noise, bearing and the body temperature is too high, the phenomenon such as outward spraying material, should immediately stop check, troubleshooting rear can continue to work. 8、Crushing material should be checked carefully to avoid copper, iron, stone and other hard objects into the crushing chamber cause an accident. 9、Operators don't wear gloves, feeding should be standing on the mill profile, in case the rebound sundry injured facial. 10、Jams, forbidden hand pulled the feed, forced feeding or stick.

2016

Feed mixing and crushing equipment

(1)Mixing equipment is the core of feed production, the equipment that the commonly used mixed type with horizontal twin screw (uniaxial) blade mixer, horizontal spiral mixer, vertical mixing machine and production waist drum type mixer in the process of the mixture. Different words to different material products of feed mixing machine requirements. Gb regulation of feed mixing uniformity coefficient of variation CV < 10%, premix mixing uniformity coefficient of variation CV < 5%, both inadequate and excessive mixed affect bar material classification, lower the quality of feed. (2)Crushing equipment such as magnetic separation machine, feeder, crusher, including many different kinds of crusher, commonly used hammer type and claw type crusher, and requires more fine granularity of micro pulverizer.

2016

Keep in mind the feed mill installation considerations

1、Mill operation for a long time, should be fixed on the basis of cement. If change often work site, grinder with the motor installed on the made of Angle iron frame, if mill diesel power, should make the two power match, namely power slightly bigger than the mill power of diesel engine, and make the pulley groove of the two is consistent, pulley end on the same plane. 2、Mill after installation to check each fastener tighten situation, if there is loose should be tightened. 3、To check whether the belt elasticity is appropriate, whether the motor shaft and crusher shaft parallel. 4、Before starting the grinder, rotating the rotor by hand, and check the tooth claw hammer, and rotor operation is flexible and reliable, and there are no collisions in the shell, rotor rotate to whether in direction arrow on board, motor and shatter machine lubrication are in good condition. 5、Don't change the pulley, in case of high speed crushing chamber to produce explosion, or low speed impact work efficiency. 6、Crushing machine idle first 2 a 3 minutes after launch, no anomalies feeding again after work. 7、Work should pay attention to the workings of the crusher of at any time, feeding wants even, in case of blocking stuffy car, don't long time overload running. If find any vibration, noise, bearing and the body temperature is too high, the phenomenon such as outward spraying material, should immediately stop check, troubleshooting rear can continue to work. 8、Crushing material should be checked carefully to avoid copper, iron, stone and other hard objects into the crushing chamber cause an accident. 9、Operators don't wear gloves, feeding should be standing on the mill profile, in case the rebound sundry injured facial. 10、Jams, forbidden hand pulled the feed, forced feeding or stick.

2016

Biomass pellet production line in our company recently exports in South Asia

Biomass pellet production line in our company recently exports in South Asia. Our company will send engineers and installation workers on-site installation guide.

2016

Congratulations to our company in Europe wood crushing drying granulating production line in the recently installed

Congratulations to our company in Europe wood crushing drying granulating production line in the recently installed. Single from our process design, equipment, and the whole production line to install later got customer's approval. This production line is for debugging. After the success of the trial run will be put into production soon. The customer said looking forward to our closer cooperation.

2016

Influence of particle machine particle length and its control measures

By the formula can be seen that Q is proportional to the particle length L and output, in the case of other parameters constant, the higher yield, the longer the particles, the shorter the vice particles. Therefore, in order to achieve a specific particle length request, to adjust the output of granulator is one possible choice method, in the actual feed production, feed manufacturers did the same, sometimes even sacrifice a lot of production to meet the requirements of particle length, the problem will be mentioned in the discussion that follows.

2016

< 1 2 3 4 >

Add: No.89, Kunlun North Road, Kunlun Economic Development Zone, Liyang City, Jiangsu Province
Marketing Department:0519-87806006 0519-87806008
13801493156
Engineering Department:0519-87808828 0519-87808798
Service Department:0519-87806000
Fax: 0519-87806088
Mailbox:cnjscxy@163.com
Zip Code: 213300
QQ：188043365

www.300.cn Changzhou | Label |

Business License

13801493156

cnjscxy@163.com

0519-87806006